blob: 9eb7664ee37138fc31731efacfa182c84c30ae0a (
about) (
plain) (
blame)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
|
Full disk encryption with Yubikey (Yubico key) for dracut
=========================================================
This allows to automatically unlock a LUKS encrypted hard disk from `systemd`-
enabled initramfs.
Requirements
------------
To compile and use yubikey full disk encryption you need:
* libyubikey-devel
* ykpers-devel
* iniparser-devel
* libarchive-devel
* cryptsetup-devel
* python-markdown
* systemd-devel
Build and install
-----------------
Building and installing is very easy. Make sure you have a Softlink from markdown to markdown_py
> ln -s /bin/markdown_py /bin/markdown
Just run:
> make
followed by:
> make install-dracut
This will place files to their desired places in filesystem.
Usage
-----
Make sure systemd knows about your encrypted device by
adding a line to `/etc/crypttab`. It should read like:
> `mapping-name` /dev/`LUKS-device` -
Normally, there is already an entry for your device.
Update `/etc/ykfde.conf` with correct settings. Add `mapping-name` from
above to `device name` in the `general` section. Then add a new section
with your key's decimal serial number containing the key slot setting.
The file should look like this:
[general]
device name = crypt
[1234567]
luks slot = 1
*Be warned*: Do not remove or overwrite your interactive key! Keep that
for backup and rescue!
`ykfde` will read its information from these files. Then prepare
the key. Plug it in, make sure it is configured for `HMAC-SHA1`.
After that run:
> ykfde
This will store a challenge in `/etc/ykfde.d/` and add a new slot to
your LUKS device. When `ykfde` asks for a password it requires a valid
password from available slot.
Build the dracut:
> dracut -f
Now you have two choices. If you want, that the challenges are updated every boot, go on. else stop here.
### change challenges on boot
To change the challenges every boot it takes too long to generate whole new initramfs. So we load an additional initram with the bootloader.
Build the cpio archive with the challenges:
> ykfde-cpio
Setup your bootloader with the the additional initram '/boot/ykfde-challenges.img'
#### Setup GRUB2
For ex. change /boot/grub2/grub.cfg
initrd /initramfs-3.10.0-123.13.2.el7.x86_64.img
to
initrd /initramfs-3.10.0-123.13.2.el7.x86_64.img /ykfde-challenges.img
with EFI /boot/efi/../grub.cfg
initrdefi /initramfs-3.17.7-300.fc21.x86_64.img
to
initrdefi /initramfs-3.17.7-300.fc21.x86_64.img /ykfde-challenges.img
### enable service
Enable `systemd` service `ykfde-cpio.service`. it generate every boot a new challenge and updates the initram `ykfde-challenges.img` and the LUKS passphrase.
*Be carefully:* Do not enable if you haven't setup the bootloader with the ykfde-challenges.img. If you do, you have to rebuild with dracut manually every time the service is executed.
Reboot and have fun!
|